Quick answer: How to read toronto zoning map?

Additionally, how do I find out the zoning of a property in Toronto? Contact a Toronto Building Customer Service counter to ask about the zoning on your property. 416-397-5330. You may call from 8:30 a.m. to 4:30 p.m., Monday to Friday. City Planning staff can answer general questions about Zoning By-law 569-2013 and about new zoning initiatives.

Furthermore, what is M2 zoning in Toronto? HEAVY INDUSTRIAL ZONE (M2)

Frequent question, what is E zoning in Toronto? In the E zone, a drive through facility must comply with the specific use regulations in Section 150.80. In the E zone, a vehicle repair shop must be on a lot that is at least 100.0 metres from a lot in the Residential Zone category or Residential Apartment Zone category.

Considering this, what is R2 zoning in Ontario? The R2 (Medium Density Residential) zoning district is established to allow for the development of a mix of single family dwellings, duplexes, townhouses, condominiums, garden apartments and other types of residential development at densities in the range of 11.1 to 16.0 dwellings per acre with an appropriate level of …Where Are Zoning Laws and Ordinances Located? The best place to look for your local laws is at the office of your city or town government. The offices of the mayor, city attorney, or department of housing, are also a good place to start. Some public libraries may also have local ordinance materials.

What is M1 zoning in Ontario?

PERMITTED USES. No land, building, or structures shall be used or erected in the Restricted Industrial Zone (M1) unless serviced by a public water supply, sanitary sewer system and storm sewer system.

How close to the property line can I build a shed?

You typically can’t build a shed within 10 feet of the rear property line and 15 feet from a side property line. There should be sufficient room between your shed and your neighbor’s yard. If there is any question, review your permit, check with your HOA, or contact your municipality office.

How big of a house can I build on my lot in Toronto?

Every neighbourhood is different. A 10,000 square foot lot in downtown Toronto allows you to build 30000 ft^2 of residential space if it has a 3x FSR. Whereas a the same size lot in Oakville will only allow you to build a 3000 square foot single family home. You can feel forced into building on that specific theme.

How do I find the zone of my property?

Visit your local zoning office, city hall, or some other local planning board and get a copy of your local ordinance. In some areas, if you have a legal description of the property (name, address, tax map, and parcel number), you can call the zoning office or city hall, or even e-mail your request for information.

What is M zoning in Ontario?

Within an Industrial “M1” Zone no person shall use any land, erect, alter, enlarge, use or maintain any building or structure for any use other than as permitted in subsection 2 of this Section and also in accordance with the regulations contained or referred to in subsections 3 and 4 of this Section.

How do I find my house code?

Beyond building to code, you need to obtain permits To obtain a permit, you or your contractor submits a plan to the local government. Once the plan is approved, you’ll be issued a permit, and you can get to work. Later on, an inspector will check the work to confirm that it meets the plan and is up to code.

What is e1 zone?

the zoning designation E -1, i. e., E- 1( 1. 5), etc. The designation E -1 without any additional numerals. designates the minimum half -acre lot size. There shall be no maximum permitted lot size.

What is a zone exception?

the special permission for a structure to be built where it contravenes the zoning laws.

How do I change my zoning in Toronto?

Individuals who wish to use, alter or develop their property in a way that does not conform with the Zoning bylaw, must apply for a site-specific amendment to the bylaw. Individuals can do this through either a Zoning bylaw Amendment application (commonly called a Rezoning) or a Minor Variance application.

What does Zone R1 mean?

The R1 Zoning is one of the most commonly found zoning types in residential neighborhoods. This particular classification allows single-family homes to be built, with one unit intended per lot.

What does R3 zoning mean in Ontario?

The R3 Zone provides for and regulates low to low-medium density residential development permitting single detached dwellings, semi-detached dwellings, duplex dwellings, triplex dwellings, fourplex dwellings; and allows for the conversion of an existing dwelling.

What is R5 zoning in Ontario?

This R5 Zone provides for and regulates medium density residential development in the form of cluster townhouses. … The higher density zone variation has been designed to accommodate stacked townhouses. The middle range zone variations are designed for most suburban townhousing developments.

What is c2 zone?

The C-2 General Commercial Zone is intended to permit a wide range of retail and commercial services, professional offices, and medical facilities.

Can I run a small business out of my home?

You can start and run your small business from the comfort of your own home. Running a business from home allows you to profit without dealing with the high overhead typical of traditional business settings. You also avoid long commutes. Running a successful small business from home isn’t always easy, however.

What is C3 zoning in Ontario?

Within the Highway Commercial (C3) Zone, no person shall use any land, erect, alter, enlarge, use or maintain any building or structure for any use other than as permitted in this section and also such use, building or structure shall be in accordance with the regulations contained or referred to in this section.

Back to top button

Adblock Detected

Please disable your ad blocker to be able to view the page content. For an independent site with free content, it's literally a matter of life and death to have ads. Thank you for your understanding! Thanks